1 |
/* RCSid $Id: interp2d.h,v 2.4 2013/02/11 22:56:22 greg Exp $ */ |
2 |
/* |
3 |
* Header for interpolation of anisotropic samples on 2-D plane. |
4 |
* |
5 |
* G.Ward Feb 2013 |
6 |
*/ |
7 |
|
8 |
#ifndef _RAD_INTERP2D_H_ |
9 |
#define _RAD_INTERP2D_H_ |
10 |
|
11 |
#ifdef __cplusplus |
12 |
extern "C" { |
13 |
#endif |
14 |
|
15 |
#define NI2DSMF 0.42f /* minimal smoothing factor */ |
16 |
|
17 |
#define NI2DIR (2*4) /* # interpolation directions */ |
18 |
|
19 |
/* Data structure for interpolant */ |
20 |
typedef struct { |
21 |
int ns; /* number of sample positions */ |
22 |
float dmin; /* minimum diameter (default=1) */ |
23 |
float smf; /* smoothing factor (def=NI2DSMF) */ |
24 |
unsigned short (*da)[NI2DIR]; /* anisotropic distances (private) */ |
25 |
float spt[1][2]; /* sample positions (extends struct) */ |
26 |
} INTERP2; |
27 |
|
28 |
/* Allocate a new set of interpolation samples (caller assigns spt[] array) */ |
29 |
extern INTERP2 *interp2_alloc(int nsamps); |
30 |
|
31 |
/* Resize interpolation array (caller must assign any new values) */ |
32 |
extern INTERP2 *interp2_realloc(INTERP2 *ip, int nsamps); |
33 |
|
34 |
/* Set minimum distance under which samples will start to merge */ |
35 |
extern void interp2_spacing(INTERP2 *ip, double mind); |
36 |
|
37 |
/* Modify smoothing parameter by the given factor */ |
38 |
extern void interp2_smooth(INTERP2 *ip, double sf); |
39 |
|
40 |
/* Assign full set of normalized weights to interpolate the given location */ |
41 |
extern int interp2_weights(float wtv[], INTERP2 *ip, double x, double y); |
42 |
|
43 |
/* Get normalized weights and indexes for n best samples in descending order */ |
44 |
extern int interp2_topsamp(float wt[], int si[], const int n, |
45 |
INTERP2 *ip, double x, double y); |
46 |
/* Free interpolant */ |
47 |
extern void interp2_free(INTERP2 *ip); |
48 |
|
49 |
/* (Re)compute anisotropic basis function interpolant (normally automatic) */ |
50 |
extern int interp2_analyze(INTERP2 *ip); |
51 |
|
52 |
/*************************************************************** |
53 |
* Typical use is to allocate an INTERP2 struct and assign the |
54 |
* spt[] array with the ordered sample locations in x & y. (The |
55 |
* actual orientation of the axes is not important so long as |
56 |
* the application is consistent.) During interpolation, either |
57 |
* interp2_weights() is called to obtain a normalized weighting |
58 |
* vector for all the samples, or interp2_topsamp() is called to |
59 |
* get the most important N samples for the specified location. |
60 |
* The weights (and indexes in the case of interp2_topsamp) |
61 |
* are then used as coefficients for corresponding sample values |
62 |
* in a vector sum that interpolates the function at that |
63 |
* location. |
64 |
* The minimum distance between sample positions defaults to 1.0. |
65 |
* Values spaced closer than this will be merged (averaged). The |
66 |
* interp2_spacing() call may be used to alter this member, |
67 |
* causing the interpolant to be recalculated during the |
68 |
* next call to either of the sampling functions. |
69 |
* The default smoothing factor NI2DSMF provides near-optimal |
70 |
* interpolation when well-separated values are known |
71 |
* precisely. Increase this setting by a factor > 1.0 |
72 |
* with the interp2_smooth() call if greater mixing is desired. |
73 |
* A call of interp2_smooth(ip,0.0) resets to the minimum |
74 |
* default. It is not possible to "sharpen" the data. |
75 |
**************************************************************/ |
76 |
|
77 |
#ifdef __cplusplus |
78 |
} |
79 |
#endif |
80 |
#endif /* !_RAD_INTERP2D_H_ */ |