| 9 |
|
][ |
| 10 |
|
.B \-V |
| 11 |
|
][ |
| 12 |
+ |
.B "\-t secs" |
| 13 |
+ |
][ |
| 14 |
|
.B "\-c count" |
| 15 |
|
][ |
| 16 |
|
.B \-fo |
| 121 |
|
.I \-c |
| 122 |
|
set to zero. |
| 123 |
|
.PP |
| 124 |
+ |
Output flushing at fixed intervals may be enabled with the |
| 125 |
+ |
.I \-x |
| 126 |
+ |
option, which specifies the number of records |
| 127 |
+ |
(-c accumulations) before each flush. |
| 128 |
+ |
If the |
| 129 |
+ |
.I \-y |
| 130 |
+ |
option is also set, then periodic flushing is disabled and the |
| 131 |
+ |
output size for an RGB image is the taken from the x and y dimensions. |
| 132 |
+ |
In lieu of periodic flushing, a flush may be forced as mentioned above |
| 133 |
+ |
by sending a sample with a zero direction vector, although you |
| 134 |
+ |
must still send a full record of rays before output occurs. |
| 135 |
+ |
.PP |
| 136 |
+ |
If progress reports are desired, the |
| 137 |
+ |
.I \-t |
| 138 |
+ |
option specifies a time interval in seconds for reports sent to |
| 139 |
+ |
standard error. |
| 140 |
+ |
This requires that the number of input samples is known, meaning a |
| 141 |
+ |
.I \-y |
| 142 |
+ |
parameter has been specified. |
| 143 |
+ |
.PP |
| 144 |
|
The output of |
| 145 |
|
.I rcontrib |
| 146 |
|
has many potential uses. |
| 180 |
|
option may be used to further define |
| 181 |
|
a "bin number" within each object if finer resolution is needed, and |
| 182 |
|
this will be applied to a "%d" format in the output file |
| 183 |
< |
specification if present. |
| 183 |
> |
specification if present. |
| 184 |
> |
(The final integer will be offset incrementally |
| 185 |
> |
if the output is a RADIANCE picture and more than one modifier has |
| 186 |
> |
the same format specification.)\0 |
| 187 |
|
The actual bin number is computed at run time based on ray direction |
| 188 |
|
and surface intersection, as described below. |
| 189 |
|
The number of bins must be specified in advance with the |
| 233 |
|
with a |
| 234 |
|
.I \-p |
| 235 |
|
option, which contains a list of variable names and assigned values, separated |
| 236 |
< |
by commas or semicolons. |
| 236 |
> |
by commas, colons, or semicolons. |
| 237 |
|
The computed bin value will be |
| 238 |
|
rounded to the nearest whole number. |
| 239 |
|
(Negative bin values will be silently ignored.)\0 |
| 305 |
|
replaced by the contents of the given file. |
| 306 |
|
.PP |
| 307 |
|
.I Rcontrib |
| 308 |
< |
has EXPERIMENTAL support for light source contributions from photon maps |
| 284 |
< |
generated by |
| 308 |
> |
supports light source contributions from photon maps generated by |
| 309 |
|
.I mkpmap(1) |
| 310 |
|
with its |
| 311 |
|
.I -apC |
| 312 |
< |
option. In photon mapping mode, |
| 312 |
> |
option. Enabling photon mapping is described in the |
| 313 |
> |
.I rtrace |
| 314 |
> |
man page along with its relevant settings. In photon mapping mode, |
| 315 |
|
.I rcontrib |
| 316 |
|
only supports contributions from light sources, not arbitrary modifiers. |
| 317 |
|
The |
| 321 |
|
.I \-V- |
| 322 |
|
option. Using fewer photons than there are light sources for the photon |
| 323 |
|
density estimates results in omitted contributions, thus the bandwidth |
| 324 |
< |
is clamped accordingly and a warning issued. |
| 324 |
> |
is clamped accordingly and a warning is issued. |
| 325 |
|
.SH EXAMPLES |
| 326 |
|
To compute the proportional contributions from sources modified |
| 327 |
< |
by "light1" vs. "light2" on a set of illuminance values: |
| 327 |
> |
by "light1" vs. "light2" on a set of irradiance values: |
| 328 |
|
.IP "" .2i |
| 329 |
|
rcontrib \-I+ @render.opt \-o c_%s.dat \-m light1 \-m light2 scene.oct < test.dat |
| 330 |
|
.PP |
| 340 |
|
.IP "" .2i |
| 341 |
|
pcomb \-c 100 90 75 c_light1.hdr \-c 50 55 57 c_light2.hdr > combined.hdr |
| 342 |
|
.PP |
| 343 |
< |
To compute an array of illuminance contributions according to a Tregenza sky: |
| 343 |
> |
To compute an array of irradiance contributions according to a Tregenza sky: |
| 344 |
|
.IP "" .2i |
| 345 |
|
rcontrib \-I+ \-f tregenza.cal \-b tbin \-bn Ntbins \-o sky.dat \-m skyglow |
| 346 |
|
\-b 0 \-o ground.dat \-m groundglow @render.opt scene.oct < test.dat |
| 352 |
|
scene.oct < test.dat, |
| 353 |
|
.SH ENVIRONMENT |
| 354 |
|
RAYPATH path to search for \-f and \-M files |
| 355 |
+ |
.SH BUGS |
| 356 |
+ |
We do not currently compute contributions or coefficients properly |
| 357 |
+ |
in scenes with participating media. |
| 358 |
+ |
A single warning will be issued if a scattering or absorbing medium |
| 359 |
+ |
is detected. |
| 360 |
|
.SH AUTHOR |
| 361 |
|
Greg Ward |
| 362 |
|
.SH "SEE ALSO" |
