man/man1/pcomb.1

.\" RCSid "$Id: pcomb.1,v 1.4 2003/12/09 15:59:06 greg Exp $"
.TH PCOMB 1 8/31/96 RADIANCE
.SH NAME
pcomb - combine RADIANCE pictures
.SH SYNOPSIS
.B pcomb
[
.B -w
][
.B "\-x xres"
][
.B "\-y yres"
][
.B "\-f file"
][
.B "\-e expr"
]
[
[
.B -o
][
.B "\-s factor"
][
.B "\-c r g b"
]
.B "input .."
]
.SH DESCRIPTION
.I Pcomb
combines equal-sized RADIANCE pictures and sends the result to the
standard output.
By default, the result is just a linear combination of
the input pictures multiplied by
.I \-s
and
.I \-c
coefficients,
but an arbitrary mapping can be assigned with the
.I \-e
and
.I \-f
options.
Negative coefficients and functions are allowed, and
.I pcomb
will produce color values of zero where they would be negative.
.PP
The variables
.I ro,
.I go
and
.I bo
specify the red, green and blue output values, respectively.
Alternatively, the single variable
.I lo
can be used to specify a brightness value for black and white output.
The predefined functions
.I ri(n),
.I gi(n)
and
.I bi(n)
give the red, green and blue input values for
picture
.I n.
To access a pixel that is nearby the current one, these functions
also accept optional x and y offsets.
For example,
.I ri(3,-2,1)
would return the red component of the pixel from picture 3
that is left 2 and up 1 from the current position.
Although x offsets may be as large as width of the picture,
y offsets are limited to a small window (+/- 8 pixels) due to efficiency
considerations.
However, it is not usually necessary to worry about this problem --
if the requested offset is not available, the next best pixel is
returned instead.
.PP
For additional convenience, the function
.I li(n)
is defined as the input brightness for picture
.I n.
This function also accepts x and y offsets.
.PP
The constant
.I nfiles
gives the number of input files present,
and
.I WE
gives the white efficacy (lumens/brightness) for pixel values,
which may be used with the
.I \-o
option or the le(n) values to convert to absolute
photometric units (see below).
The variables
.I x
and
.I y
give the current output pixel location for use in
spatially dependent functions, the constants
.I xmax
and
.I ymax
give the input resolution, and the constants
.I xres
and 
.I yres
give the output resolution (usually the same, but see below).
The constant functions
.I "re(n), ge(n), be(n),"
and
.I le(n)
give the exposure values for picture
.I n,
and
.I pa(n)
gives the corresponding pixel aspect ratio.
Finally, for pictures with stored view parameters,
the functions
.I "Ox(n), Oy(n)"
and
.I Oz(n)
return the ray origin in world coordinates for the current pixel
in picture
.I n,
and
.I "Dx(n), Dy(n)"
and
.I Dz(n)
return the normalized ray direction.
In addition, the function
.I T(n)
returns the distance from the origin to the aft clipping plane
(or zero if there is no aft plane), and the function
.I S(n)
returns the solid angle of the current pixel in steradians
(always zero for parallel views).
If the current pixel is outside the view region,
.I T(n)
will return a negative value, and
.I S(n)
will return zero.
.PP
The
.I \-w
option can be used to suppress warning messages about invalid
calculations.
The
.I \-o
option indicates that original pixel values are to be used for the next
picture, undoing any previous exposure changes or color correction.
.PP
The
.I \-x
and
.I \-y
options can be used to specify the desired output resolution,
.I xres
and
.I yres,
and can be expressions involving other constants such as
.I xmax
and
.I ymax.
The constants
.I xres
and
.I yres
may also be specified in a file or expression.
The default output resolution is the same as the input resolution.
.PP
The
.I \-x
and
.I \-y
options must be present if there are no input files, when
the definitions of
.I ro,
.I go
and
.I bo
will be used to compute each output pixel.
This is useful for producing simple test pictures for various
purposes.
(Theoretically, one could write a complete renderer using just the
functional language...)
.PP
The standard input can be specified with a hyphen ('-').
A command that produces a RADIANCE picture can be given in place of a file 
by preceeding it with an exclamation point ('!').
.SH EXAMPLES
To produce a picture showing the difference between pic1 and pic2:
.IP "" .2i
pcomb -e 'ro=ri(1)-ri(2);go=gi(1)-gi(2);bo=bi(1)-bi(2)' pic1 pic2 > diff
.PP
Or, more efficiently:
.IP "" .2i
pcomb pic1 -s -1 pic2 > diff
.PP
To precompute the gamma correction for a picture:
.IP "" .2i
pcomb -e 'ro=ri(1)^.4;go=gi(1)^.4;bo=bi(1)^.4' pic > pic.gam
.PP
To perform some special filtering:
.IP "" .2i
pcomb -f myfilt.cal -x xmax/2 -y ymax/2 input.pic > filtered.pic
.PP
To make a picture of a dot:
.IP "" .2i
pcomb -x 100 -y 100 -e 'ro=b;go=b;bo=b;b=if((x-50)^2+(y-50)^2-25^2,0,1)' > dot
.SH AUTHOR
Greg Ward
.SH "SEE ALSO"
getinfo(1), icalc(1), pcompos(1), pfilt(1), rpict(1)
Revision:	1.5
Committed:	Thu Jan 1 19:31:45 2004 UTC (21 years, 10 months ago) by greg
Branch:	MAIN
CVS Tags:	rad3R6P1, rad3R6
Changes since 1.4:	+2 -2 lines
Log Message:	Renamed rview, lam, calc, and neat to rvu, rlam, icalc, and neaten
#	User	Rev	Content
1	greg	1.5	.\" RCSid "$Id: pcomb.1,v 1.4 2003/12/09 15:59:06 greg Exp $"
2	greg	1.1	.TH PCOMB 1 8/31/96 RADIANCE
3			.SH NAME
4	greg	1.2	pcomb - combine RADIANCE pictures
5	greg	1.1	.SH SYNOPSIS
6			.B pcomb
7			[
8			.B -w
9			][
10			.B "\-x xres"
11			][
12			.B "\-y yres"
13			][
14			.B "\-f file"
15			][
16			.B "\-e expr"
17			]
18			[
19			[
20			.B -o
21			][
22			.B "\-s factor"
23			][
24			.B "\-c r g b"
25			]
26			.B "input .."
27			]
28			.SH DESCRIPTION
29			.I Pcomb
30			combines equal-sized RADIANCE pictures and sends the result to the
31			standard output.
32			By default, the result is just a linear combination of
33			the input pictures multiplied by
34			.I \-s
35			and
36			.I \-c
37			coefficients,
38			but an arbitrary mapping can be assigned with the
39			.I \-e
40			and
41			.I \-f
42			options.
43			Negative coefficients and functions are allowed, and
44			.I pcomb
45			will produce color values of zero where they would be negative.
46			.PP
47			The variables
48			.I ro,
49			.I go
50			and
51			.I bo
52			specify the red, green and blue output values, respectively.
53			Alternatively, the single variable
54			.I lo
55			can be used to specify a brightness value for black and white output.
56			The predefined functions
57			.I ri(n),
58			.I gi(n)
59			and
60			.I bi(n)
61			give the red, green and blue input values for
62			picture
63			.I n.
64			To access a pixel that is nearby the current one, these functions
65			also accept optional x and y offsets.
66			For example,
67			.I ri(3,-2,1)
68			would return the red component of the pixel from picture 3
69			that is left 2 and up 1 from the current position.
70			Although x offsets may be as large as width of the picture,
71			y offsets are limited to a small window (+/- 8 pixels) due to efficiency
72			considerations.
73			However, it is not usually necessary to worry about this problem --
74			if the requested offset is not available, the next best pixel is
75			returned instead.
76			.PP
77			For additional convenience, the function
78			.I li(n)
79			is defined as the input brightness for picture
80			.I n.
81			This function also accepts x and y offsets.
82			.PP
83			The constant
84			.I nfiles
85			gives the number of input files present,
86			and
87			.I WE
88	greg	1.3	gives the white efficacy (lumens/brightness) for pixel values,
89			which may be used with the
90			.I \-o
91			option or the le(n) values to convert to absolute
92			photometric units (see below).
93	greg	1.1	The variables
94			.I x
95			and
96			.I y
97			give the current output pixel location for use in
98			spatially dependent functions, the constants
99			.I xmax
100			and
101			.I ymax
102			give the input resolution, and the constants
103			.I xres
104			and
105			.I yres
106			give the output resolution (usually the same, but see below).
107			The constant functions
108			.I "re(n), ge(n), be(n),"
109			and
110			.I le(n)
111			give the exposure values for picture
112			.I n,
113			and
114			.I pa(n)
115			gives the corresponding pixel aspect ratio.
116			Finally, for pictures with stored view parameters,
117			the functions
118			.I "Ox(n), Oy(n)"
119			and
120			.I Oz(n)
121			return the ray origin in world coordinates for the current pixel
122			in picture
123			.I n,
124			and
125			.I "Dx(n), Dy(n)"
126			and
127			.I Dz(n)
128			return the normalized ray direction.
129			In addition, the function
130			.I T(n)
131			returns the distance from the origin to the aft clipping plane
132			(or zero if there is no aft plane), and the function
133			.I S(n)
134			returns the solid angle of the current pixel in steradians
135			(always zero for parallel views).
136			If the current pixel is outside the view region,
137			.I T(n)
138			will return a negative value, and
139			.I S(n)
140			will return zero.
141			.PP
142			The
143			.I \-w
144			option can be used to suppress warning messages about invalid
145			calculations.
146			The
147			.I \-o
148			option indicates that original pixel values are to be used for the next
149			picture, undoing any previous exposure changes or color correction.
150			.PP
151			The
152			.I \-x
153			and
154			.I \-y
155			options can be used to specify the desired output resolution,
156			.I xres
157			and
158			.I yres,
159			and can be expressions involving other constants such as
160			.I xmax
161			and
162			.I ymax.
163			The constants
164			.I xres
165			and
166			.I yres
167			may also be specified in a file or expression.
168			The default output resolution is the same as the input resolution.
169			.PP
170			The
171			.I \-x
172			and
173			.I \-y
174			options must be present if there are no input files, when
175			the definitions of
176			.I ro,
177			.I go
178			and
179			.I bo
180			will be used to compute each output pixel.
181			This is useful for producing simple test pictures for various
182			purposes.
183			(Theoretically, one could write a complete renderer using just the
184			functional language...)
185			.PP
186			The standard input can be specified with a hyphen ('-').
187			A command that produces a RADIANCE picture can be given in place of a file
188			by preceeding it with an exclamation point ('!').
189			.SH EXAMPLES
190			To produce a picture showing the difference between pic1 and pic2:
191			.IP "" .2i
192			pcomb -e 'ro=ri(1)-ri(2);go=gi(1)-gi(2);bo=bi(1)-bi(2)' pic1 pic2 > diff
193			.PP
194			Or, more efficiently:
195			.IP "" .2i
196			pcomb pic1 -s -1 pic2 > diff
197			.PP
198			To precompute the gamma correction for a picture:
199			.IP "" .2i
200			pcomb -e 'ro=ri(1)^.4;go=gi(1)^.4;bo=bi(1)^.4' pic > pic.gam
201			.PP
202			To perform some special filtering:
203			.IP "" .2i
204			pcomb -f myfilt.cal -x xmax/2 -y ymax/2 input.pic > filtered.pic
205			.PP
206			To make a picture of a dot:
207			.IP "" .2i
208			pcomb -x 100 -y 100 -e 'ro=b;go=b;bo=b;b=if((x-50)^2+(y-50)^2-25^2,0,1)' > dot
209			.SH AUTHOR
210			Greg Ward
211			.SH "SEE ALSO"
212	greg	1.5	getinfo(1), icalc(1), pcompos(1), pfilt(1), rpict(1)